1.Occupational Safety & Health:Basic first aid, safety signs – for Danger, Warning, caution & personal safety message.

2.Occupational Safety & Health:Safe handling of Fuel Spillage, Fire extinguishers used for different types of fire.

3.Occupational Safety & Health:Importance of Occupational Safety & Health, handling and Periodic testing of lifting equipment.

4.Occupational Safety & Health:Safety, Safety sign, Safe disposal of toxic dust.

5.Occupational Safety & Health:Authorization of Moving & road testing vehicles , Artificial respiration in primary treatment.

6.Occupational Safety & Health:electrical safety , Types of Fire extinguisher, First Aid material, Safety disposal of Used engine oil.

7.Energy conservation-Definition, Energy Conservation Opportunities.(ECOs)-Minor ECos and Medium ECOs, Major ECOs).

8.Energy conservation-Short answer type question.

9.Revision of all topic:MCQ practice & Short type question.

10.Introduction to road safety and Automotive emissions:Introduction to road safety ,Introduction of Automotive emissions.

11.Hand & Power Tools:Marking scheme, Marking material-chalk, Prussian blue. Surface gauge.

12.Hand & Power Tools:Cleaning tools- Scraper, wire brush, Emery paper, Description, care and use of Surface plates.

13.Hand & Power Tools:steel rule, measuring tape, try square. Callipers-inside and outside.

14.Hand & Power Tools:Dividers, surface gauges, scriber, Chisel-flat, cross-cut.

15.Hand & Power Tools:punches-prick punch, centre punch, pin punch, hollow punch, number and letter punch.

16.Hand & Power Tools:Hammer- ball peen, lump, mallet.

17.Hand & Power Tools:Screw drivers-blade screwdriver, Phillips screw driver, Ratchet screwdriver. Allen key, bench vice & C-clamps.

18.Hand & Power Tools:Spanners- ring spanner, open end spanner & the combination spanner, universal adjustable open end spanner.

19.Hand & Power Tools:Pliers – Combination pliers, multi grip, long nose, flat-nose.

20.Hand & Power Tools:Nippers or pincer pliers, Side cutters, Tin snips, Circlips
pliers, external circlips pliers.

21.Hand & Power Tools:Air impact wrench, air ratchet, wrenches- Torque wrenches, pipe wrenches.

22.Hand & Power Tools:car jet washers Pipe flaring & cutting tool, pullers-Gear and bearing.

23.Systems of measurement:Description, care & use of – Micrometers.

24.Systems of measurement:Description, care & use of – VERNIER CALIPER.

25.Systems of measurement:Difference between vernier & micrometer. Introduction of gauges.

26.Systems of measurement:TYPES OF GAUGE : vacuum gauge, tire pressure gauge, Dial indicators, straightedge, feeler gauge thread pitch gauge.

27.Systems of measurement:REVISION OF ALL TOPIC & MCQ PRACTICE.

28.Drilling machine:Description and study of Bench type Drilling machine.

29.Drilling machine:Portable electrical Drilling machine.

30.Drilling machine:drill holding devices.

31.Drilling machine:Work Holding devices, Drill bits.

32.Taps and Dies:Hand Taps and wrenches.

33.Taps and Dies:Calculation of Tap drill sizes for metric and inch taps.

34.Taps and Dies:Different type of Die and Die stock.Screw extractors.

35.Hand Reamers:Different Type of hand reamers,Drill size for reaming.

36.Hand Reamers:Lapping, Lapping abrasives.

37.Hand Reamers:type of Laps.

38.Basic electricity:Electricity principles,Ground connections, Ohm’s law,Voltage, Current, Resistance, Power,Energy. Voltmeter, ammeter.

39.Basic electricity:Ohmmeter Mulitmeter, Conductors & insulators,Wires, Shielding, Length vs. resistance,Resistor ratings.

40.Basic electricity:Wires, Shielding, Length vs. resistance,Resistor ratings.

41.Basic electricity:Fuses & circuit breakers, Ballast resistor.

42.Basic electricity:Stripping ,wire insulation, cable colour codes and sizes.

43.Basic electricity:Resistors in Series circuits , Parallel circuits and Series-parallel circuits, Electrostatic effects.

44.Basic electricity:Capacitors and its applications, Capacitors in series and parallel.

45.Basic electricity:Description of Chemical effects, Batteries & cells.

46.Basic electricity:Lead acid batteries & Stay Maintenance Free (SMF) batteries.

47.Basic electricity:Magnetic effects, Heating effects,Thermo-electric energy, Thermisters.

48.Basic electricity:Thermo couples, Electrochemical energy, Photo-voltaic energy, Piezoelectric energy.

49.Basic electricity:Electromagnetic induction, Relays, Solenoids, Primary & Secondary windings, Transformers, stator and rotor coils.

50.Basic electronics:Description of Semi conductors.

51.Basic electronics:Solid state devices- Diodes, Transistors, Thyristors, Uni Junction Transistors ( UJT).

52.Basic electronics:Metal Oxide Field Effect Transistors ( MOSFETs).

53.Introduction to Hydraulics & Pneumatics: #NAME?

54.Introduction to Hydraulics & Pneumatics:Description, symbols and application in automobile of Gear pumpInternal & External.

55.Introduction to Hydraulics & Pneumatics:single acting, double acting & Double ended cylinder.

56.Introduction to Hydraulics & Pneumatics:Directional control valves2/2, 3/2, 4/2, 4/3 way valve, Pressure relief valve.

57.Introduction to Hydraulics & Pneumatics: Non return valve, Flow control valve used in automobile.

58.Introduction to Hydraulics & Pneumatics:Pneumatic Symbols, Description and function of air Reciprocating Compressor.

59.Introduction to Hydraulics & Pneumatics:Function of Air service unit (FRL-Filter, Regulator & Lubricator).

60.Auto Industry:#NAME?

61.Auto Industry:Brief about Ministry of Road transport & Highways, The Automotive Research Association of India (ARAI).

62.Auto Industry:National Automotive Testing and R&D Infrastructure Project (NATRIP), & Automobile Association.

63.Auto Industry:Definition: – Classification of vehicles on the basis of load as per central motor vehicle rule.

64.Auto Industry:wheels, final drive, and fuel used, axles, position of engine and steering transmission, body and load.

65.Auto Industry:Brief description and uses of Vehicle hoists – Two post and four post hoist, Engine hoists, Jacks, Stands.

66.Introduction to Engine:Description of internal & external combustion engines, Classification of IC engines.

67.Introduction to Engine:Principle & working of 2&4-stroke diesel engine (Compression ignition Engine (C.I)).

68.Introduction to Engine:Principle of Spark Ignition Engine(SI), differentiate between 2- stroke and 4 stroke.

69.Introduction to Engine:C.I engine and S.I Engine”Direct injection and Indirect injection, Technical terms used in engine, Engine specification.”

70.Introduction to Engine:Study of various gauges/instrument on a dash board of a vehicleSpeedometer, Tachometer, Odometer and Fuel gauge, and Indicators such as gearshift position.

71.Introduction to Engine:Seat belt warning light, Parking-brakeengagement warning light and an Engine-malfunction light.

72.Introduction to Engine:Different type of starting and stopping method of Diesel Engine Procedure for dismantling of diesel engine from a vehicle.

73.Petrol Engine Basics:4-stroke spark-ignition engines- Basic 4-stroke principles.

74.Petrol Engine Basics:Spark-ignition engine components- Basic engine components, Engine cams & camshaft.

75.Petrol Engine Basics:Engine power transfer, Scavenging, Counter weights, Piston components.

76.Petrol Engine Basics:Intake & exhaust systems – Electronic fuel injection systems, Exhaust systems. Intake system components.

77.Petrol Engine Basics:Air cleaners, Carburettor air cleaners, EFI air cleaners, Intake manifolds, Intake air heating.

78.Petrol Engine Basics: Gasoline Fuel Systems:Description of Gasoline fuel, characteristics.

79.Petrol Engine Basics:Controlling fuel burn, Stoichiometric ratio, Air density, Fuel supply system, Pressure & vacuum.

80.Engine Components:Description and Constructional feature of Cylinder head.

81.Engine Components:Importance of Cylinder head design, Type of Petrol and Diesel combustion chambers,exhaust passages, Head gaskets. Importance of Turbulence.

82.Valves & Valve Trains:Description and Function of Engine Valves, different types, materials, Type of valve operating mechanism.

83.Valves & Valve Trains:Importance of Valve seats, and Valve seats inserts in cylinder heads, importance of Valve rotation, Valve stem oil seals.

84.Valves & Valve Trains:size of Intake valves, Valve trains, Valvetiming diagram, concept of Variable valve timing.

85.Valves & Valve Trains:Description of Camshafts & drives , Description of Overhead camshaft, importance of Cam lobes,Valves & Valve Trains.

86.Engine Components/PISTON.:Description & functions of different types of pistons, piston rings and piston pins and materials.

87.Engine Components:Used recommended clearances for the rings and its necessity precautions while fitting rings, common troubles and remedy. Compression ratio.

88.Engine Components:Description & function of connecting rod, importance of big- end split obliquely, Materials used for connecting rods big end & main bearings.

89. Engine Components/CRANKSHAFT:Shells piston pins and locking methods of piston pins.Description and function of Crank shaft,camshaft.

90.Engine Components:Engine bearingsclassification and location – materials used & composition of bearing materials- Shell bearing and their advantages.

91.Engine Components:special bearings material for diesel engine application bearing failure & its causes-care & maintenance.

92.Engine Components:Crank-shaft balancing, Firing order of the engine.

93.Engine Components/FLYWHEEL:Description and function of the fly wheel,vibration damper,Crank case & oil pump.

94.Engine Components:gears timing mark, Chain sprockets,chain tensioner etc.

95.Engine Components:Function of clutch & coupling units attached to flywheel.Description of Cylinder block.

96.Engine Components:ion of Cylinder block, Cylinder block construction,Different type of Cylinder sleeves (liner).

97.Need for Cooling systems:Heat transfer method, Boiling point & pressure, Centrifugal force.

98.Need for Cooling systems:Vehicle coolant properties and recommended change of interval, Different type of cooling systems.

99.Basic cooling system components:Radiator,Coolant hoses, Water pump,cooling system thermostat ,cooling fans.

100.Basic cooling system components:Temperature indicators, Radiator pressure cap, Recovery system, Thermo-switch.

101.Need for lubrication system:Functions of oil, Viscosity and its grade as per SAE , Oil additives, Synthetic oils, The lubrication system.

102.Splash system:Pressure system, Corrosion/noise reduction in the lubrication system. Lubrication system components.

103. Splash system:Description and function of Sump, Oil collection pan, Oil tank, Pickup tube.

104.Splash system:different type of Oil pump & Oil filters Oil pressure relief valve, Spurt holes & galleries, Oil indicators, Oil cooler.

105.Intake system components:Description and function of Air cleaners, Different type air cleaner.

106.Intake system components:Description of Intake manifolds and material.

107.Exhaust system components:Description and function of Exhaust manifold, Exhaust pipe, Extractors.

108.Exhaust system components:MufflersReactive, absorptive, Combination,Catalytic converters, Flexible connections.

109.Exhaust system components:Ceramic coatings, Back-pressure, Electronic mufflers.

110.Diesel Fuel Systems:Description and function of Diesel fuel injection, fuel characteristics,concept of Quiet diesel technology & Clean diesel technology.

111.Diesel fuel system components:Description and function of Diesel tanks & lines, Diesel fuel filters, water separator.

112.Diesel fuel system components:Lift pump, Plunger pump, Priming pump.

113.Inline injection pump:Distributor-type injection pump, Diesel injectors, Glow plugs, Cummins & Detroit Diesel injection.

114.Electronic Diesel control:Electronic Diesel control systems, Common Rail Diesel Injection (CRDI) system.

115.Electronic Diesel control:Hydraulically actuated electronically controlled unit injector (HEUI) diesel injection system.

116.Electronic Diesel control:Sensors, actuators and ECU (Electronic Control Unit) used in Diesel Engines.

117.Engine assembly:procedure with aid of special tools and gauges used for engine assembling.

118.Engine assembly:procedure with aid of special tools and gauges used for engine assembling.

119.Engine assembly:Introduction to Gas Turbine,Comparison of single and two stage turbine engine.

120.Engine assembly:Different between gas turbine and Diesel Engine,Different between gas turbine and Diesel Engine.

121.Emission Control:Vehicle emissions,Standards- Euro and Bharat II, III, IV, V Sources of emission,Combustion, Combustion chamber design.

122.Emission Control:Types of emissions: Characteristics and Effect of Hydrocarbons.

123.Emission Control:Hydrocarbons in exhaust gases, Oxides of nitrogen, Particulates,Carbon monoxide, Carbon dioxide, Sulphur content in fuels Description of Evaporation emission control.

124.Emission Control:Carbon monoxide, Carbon dioxide, Sulphur content in fuels Description of Evaporation emission control.

125.Emission Control:Catalytic conversion, Closed loop, Crankcase emission control, Exhaust gas recirculation (EGR) valve.

126.charging circuit:Description .of charging circuit operation of alternators,regulator unit.

127.charging circuit:ignition warning lamptroubles and remedy in charging system.

128.charging circuit:Description of starter motor circuit,Constructional details of starter motor solenoid switches.

129.charging circuit:common troubles and remedy in starter circuit.

130.Troubleshooting:Causes and remedy for Engine Not starting.

131.Troubleshooting:Causes and remedy for Engine Not starting Mechanical & Electrical causes.

132.Troubleshooting:High fuel consumption, Engine overheating,Low Power Generation.

133.Troubleshooting:Excessive oil consumption,Low/High Engine Oil Pressure, Engine Noise.

134.Project Work:Testing of engine after assembling.

135.Project Work:Intake and Exhaust System.

136.Project Work:Emission control.

137.Project Work:Charging system.

138.Project Work:Vehicle Troubleshooting.

LESSON PLAN OF WORKSHOP CALCULATION & SCIENCE 1ST YEAR :-

1.Unit, Fractions:Classification of Unit System.

2.Unit, Fractions:Fundamental and Derived Units F.P.S, C.G.S, M.K.S and SI Units.

3.Unit, Fractions:Measurement Units and Conversion.

4.Unit, Fractions:Factors, HCF, LCM and Problems.

5.Unit, Fractions:Fractions – Addition, Subtraction, Multiplication and Division.

6.Unit, Fractions:Decimal Fractions – – Addition, Subtraction, Multiplication and Division.

7.Unit, Fractions:Solving Problems by using calculator.

8.Square Root: Ratio and Proportions, Percentage:Square and Square Root.

9.Square Root: Ratio and Proportions, Percentage:Simple problems using calculator.

10.Square Root: Ratio and Proportions, Percentage:Application of Pythagoras Theorem and related problems.

11.Square Root: Ratio and Proportions, Percentage:Ratio and Proportions.

12.Square Root: Ratio and Proportions, Percentage:Direct and Indirect proportion.

13.Square Root: Ratio and Proportions, Percentage:Percentage.

14.Square Root: Ratio and Proportions, Percentage:Changing percentage to decimal.

15.Material Science:Types of metals.

16.Material Science:Physical and Mechanical Properties of metals.

17.Material Science:Types of ferrous and non-ferrous metals.

18.Material Science:Introduction of iron and cast iron.

19.Material Science:Difference between iron and steel, alloy steel and carbon steel.

20.Material Science:Properties and uses of rubber, timber and insulating materials.

21.Mass, Weight, Volume, and Density:Mass, volume, density, weight & specific gravity.

22.Mass, Weight, Volume, and Density:Related problems for mass, volume, density, weight & specific gravity.

23.Speed and Velocity, Work Power and Energy:Rest, motion, speed, velocity.

24.Speed and Velocity, Work Power and Energy:difference between speed and velocity.

25.Speed and Velocity, Work Power and Energy:acceleration and retardation.

26.Speed and Velocity, Work Power and Energy:Related problems on speed and velocity.

27.Speed and Velocity, Work Power and Energy:Potential energy, Kinetic Energy.

28.Speed and Velocity, Work Power and Energy:Potential energy, Kinetic Energy and related problems with related problems.

29.Speed and Velocity, Work Power and Energy:Work, power, energy, HP, IHP, BHP and efficiency.

30.Heat &Temperature and Pressure:Concept of heat and temperature, effects of heat, difference between heat and temperature.

31.Heat &Temperature and Pressure:Scales of temperature, Celsius, Farenhieght,Kelvin and Conversion between scales of temperature.

32.Heat &Temperature and Pressure:Temperature measuring instruments, types of thermometer, pyrometer.

33.Heat &Temperature and Pressure:Transmission of heat – Conduction, convection and radiation.

34.Heat &Temperature and Pressure:Co-efficient of linear expansion and related problems with assignments.

35.Heat &Temperature and Pressure:Problem of Heat loss and heat gain with assignments.

36.Heat &Temperature and Pressure:Thermal conductivity and insulators.

37.Heat &Temperature and Pressure:Boiling point and melting point of different metals and Nonmetals.

38.Heat &Temperature and Pressure:Concept of pressure and its units in different system.

39.Basic Electricity:Introduction and uses of electricity, molecule, atom, how electricity is produced.

40.Basic Electricity:electric current AC, DC and their comparison, voltage , resistance and their units.

41.Basic Electricity:Conductor, Insulator, types of connections- Series and Parallel.

42.Basic Electricity:Ohm’s Law, relation between VIR & related problems.

43.Basic Electricity:Electrical power, energy and their units, calculation with assignments.

44.Basic Electricity:Magnetic induction, self and mutual inductance and EMF generation.

45.Basic Electricity:Electrical Power, HP, Energy and units of electrical energy.

46.Mensuration:Area and perimeter of square, rectangle and parallelogram.

47.Mensuration:Area an Perimeter of Triangle.

48.Mensuration:Area and Perimeter of Circle, Semi-circle , circular ring, sector of circle, hexagon and ellipse.

49.Mensuration:Surface area and Volume of solids- cube, cuboids, cylinder, sphere and hollow cylinder.

50.Mensuration:Finding lateral surface area , total surface area and capacity in liters of hexagonal, conical and cylindrical shaped vessels.

51.Levers and Simple Machines:Simple machines, Effort and load, mechanical advantage, velocity ratio.

52.Levers and Simple Machines:efficiency of machine, relation between efficiency, velocity ratio and mechanical advantage.

53.Levers and Simple Machines:relation between efficiency, velocity ratio and mechanical advantage.

54.Levers and Simple Machines:Lever and its types.

55.Trigonometry:Measurement of Angle, Trigonometrical Ratios, Trigonometric Table.

56.Trigonometry:Trigonometry-Application in calculating height and distance (Simple Applications).

EMPLOYABILITY SKILL 1ST YEAR :-

1.Behavioural Skills:Expectation Setting.

2.Behavioural Skills:Personal Strength Analysis/Strength Blindness.

3.Behavioural Skills:Display Professionalism at the institute and work place.

4.Behavioural Skills:Increased social initiations relationships and networks Acceptance of peers from different cultures and social groups and work with them.

5.Behavioural Skills:Collaboration with team to prioritize the common goal and compromise individual priorities.

6.Behavioural Skills:Characteristic of a responsible citizen- Display the same by respecting self, others, environment, care for duty and value for time.

7.Behavioural Skills:Adopting best practices and aspire to follow success stories of individual for personal development.

8.English Literacy:Functional English.

9.English Literacy:Importance of Learning English Different Naming words, Words used for replacing names, Action words, Describing people, place and their use.

10.English Literacy:Simple present, past; present, past progressive Construction of simple sentences – Kinds of sentences.

11.English Literacy:Introduction to punctuation – Comma, Full stop, Question mark. Singular plural Change of tense .

12.English Literacy:Usage of appropriate words to express themselves Greetings & Self Introduction Asking &responding to questions Sharing information with others Formal & Informal communication.

13.English Literacy:Speak and provide information about workplace Discussions on current happenings.

14.English Literacy:Reading simple sentences about: a) Self b) Work c) Environment.

15.English Literacy:Simple writing skills.

16.Communication Skills:Self- Introduction.

17.Communication Skills:Perception Management.

18.Communication Skills:a. Verbal Communication.

19.Communication Skills:b. Non-Verbal Communication.

20.Communication Skills:Campus to Work.

21.I.T. Literacy:Basics of Computers.

22.I.T. Literacy:Operating System.

23.I.T. Literacy:MS-Word , MS-Excel.

24.I.T. Literacy:Web browsers & Search Engines.

25.I.T. Literacy:Email,Mobile application.

26.Entrepreneurship Skills:Need of becoming entrepreneur.

27.Entrepreneurship Skills:Ways to become a good entrepreneur.

28.Entrepreneurship Skills:Enabling environment available to become an entrepreneur.

29.Entrepreneurship Skills:Different Govt. institutions/schemes promoting Entrepreneur viz., Gramin banks, PMMY-MUDRA loans, DIC, SIDA, SISI, NSIC, SIDO.

30.Entrepreneurship Skills:Ways to set up an enterprise and different aspects involved viz., legal compliances, Marketing aspect, Budgeting, etc.

31.Entrepreneurship Skills:Day to day monitoring mechanism for Maintaining an enterprise.

32.Entrepreneurship Skills:Different Government schemes supporting entrepreneurship.

33.Entrepreneurship Skills:Examples of successful and unsuccessful entrepreneurs.

34.Maintaining Efficiency:Factors affecting productivity,Improving Productivity.

35.Maintaining Efficiency:Personal finance literacy Planning, Saving, Tax, Govt.

36.Maintaining Efficiency:schemes for financial safety e.g. Pradhan Mantri Jeevan Jyoti Bima Yojana (PMJJBY), etc.

37.Occupational Safety, Health and Environment Education Duration:Safety and Health,Occupational Hazards.

38.Occupational Safety, Health and Environment Education Duration:Accident and Safety,First-aid ,Basic provisions on safety and Health.

39.Occupational Safety, Health and Environment Education Duration:Environmental Issues,Environmental ethics,Disaster Management.

40.Essential skills for success:Building basic skills to navigate life and career. Self-Awareness, articulating personal values, Value-based decision making, Dilemma situations.

41.Essential skills for success:Identify sources and types of stress (positive / negative stress), Managing stress (long-term / short-term), Handling rejection and building resilience, Identify day wasters.

42.Labour Welfare Legislation:Benefits guaranteed under various acts- Factories Act, Apprenticeship Act, Employees State Insurance Act (ESI).

43.Labour Welfare Legislation:Payment Wages Act, Employees Provident Fund Act, The Workmen’s compensation Act, POSH. Interpret applicable labour and industrial laws.

44.Quality Management:Quality Concept and Consciousness,Concept of Quality
Management (QMS) & PDCA ,Concept of ISO.

45.Preparation to the world of work:Career Plan,Basic Professional Skills.

46.Preparation to the world of work:Career Pathways,Search and apply for a job.

47.Customer Interaction / service:Greeting customers,Probing-understanding
customer requirements.

48.Customer Interaction / service:Handling grievances,Relationship building with customers.

49.Customer Interaction / service:To identify the importance of probing.

50.Customer Interaction / service:Analyasis of whole topic.

ENGINEERING DRAWING 1ST YEAR :-

1.Engineering Drawing – Introduction:Introduction to Engineering Drawing and Drawing Instruments – • Conventions •.

2.Engineering Drawing – Introduction:Viewing of engineering drawing sheets. • Method of Folding of printed Drawing sheet as per BIS SP: 46-2003

3.Drawing Instrument:Drawing board, T-square, Drafter (Drafting M/c), Set squares, Protector, Drawing Instrument Box (Compass, Dividers, Scale, Diagonal Scales etc.), pencils of different grades, Drawing pins/ Clips.PART-01

4.Drawing Instrument:Drawing board, T-square, Drafter (Drafting M/c), Set squares, Protector, Drawing Instrument Box (Compass, Dividers, Scale, Diagonal Scales etc.), pencils of different grades, Drawing pins/ Clips.PART-02

5.Free hand drawing:Lines, polygons, ellipse etc.

6.Free hand drawing:Geometrical figures and blocks with dimension.

7.Free hand drawing:Transferring measurement from the given object to the free hand sketches.

8.Free hand drawing:Solid objects – Cube, Cuboids, Cone, Prism, Pyramid, Frustum of Cone with dimensions.

9.Free hand drawing:Free hand drawing of hand tools and measuring tools, simple fasteners (nuts, bolts, rivets etc.) trade related sketches.

10.Lines:Definition, types and applications in drawing as per BIS: 46- 2003

11.Lines:Classification of lines (Hidden, centre, construction, extension, Dimension, Section).

12.Lines:Drawing lines of given length (Straight, curved).

13.Lines:Drawing of parallel lines, perpendicular line.

14.Lines:Methods of Division of line segment.

15.Drawing of Geometrical figures:Angle: Measurement and its types, method of bisecting.

16.Drawing of Geometrical figures:Triangle: different types.

17.Drawing of Geometrical figures:Rectangle, Square, Rhombus, Parallelogram.

18.Drawing of Geometrical figures:Circle and its elements.

19.Drawing of Geometrical figures:Different polygon and their values of included angles. Inscribed and circumscribed polygons.

20.Lettering & Numbering:Single Stroke, Double Stroke, Inclined.

21.Lettering & Numbering:Single Stroke, Double Stroke, Inclined.

22.Lettering & Numbering:Single Stroke, Double Stroke, Inclined.

23.Dimensioning and its Practice:Definition, types and methods of dimensioning (functional, non-functional and auxiliary).

24.Dimensioning and its Practice:Position of dimensioning (Unidirectional, Aligned).

25.Dimensioning and its Practice:Types of arrowhead.

26.Dimensioning and its Practice:Leader line with text.

27.Dimensioning and its Practice:Symbols preceding the value of dimension and dimensional tolerance.

28.Sizes and layout of drawing sheets:Selection of sizes.

29.Sizes and layout of drawing sheets:Title Block, its position and content.

30.Sizes and layout of drawing sheets:Item Reference on Drawing Sheet (Item list).

31.Method of presentation of Engg. Drawing:Pictorial View.

32.Method of presentation of Engg. Drawing:Orthographic View.

33.Method of presentation of Engg. Drawing:Isometric View.

34.Symbolic representation – different symbols used in the trades:Fastener (Rivets, Bolts and Nuts).

35.Symbolic representation – different symbols used in the trades:Bars and profile sections.

36.Symbolic representation – different symbols used in the trades:Weld, Brazed and soldered joints.

37.Symbolic representation – different symbols used in the trades:Electrical and electronics element.

38.Symbolic representation – different symbols used in the trades:Piping joints and fitting.

39.Projections:Concept of axes plane and quadrant.

40.Projections:Concept of axes plane and quadrant.

41.Projections:Orthographic projections.

42.Projections:Orthographic projections.

43.Projections:Method of first angle and third angle projections (definition and difference).

44.Projections:Method of first angle and third angle projections (definition and difference).

45.Projections:Symbol of 1st angle and 3rd angle projection in 3rd angle.

46.Projections:Symbol of 1st angle and 3rd angle projection in 3rd angle.

47.Orthographic projection from isometric projection:Orthographic projection from isometric projection.

48.Orthographic projection from isometric projection:Orthographic projection from isometric projection.

49.Orthographic projection from isometric projection:Orthographic projection from isometric projection.

50.Orthographic projection from isometric projection:Orthographic projection from isometric projection.

51.Orthographic projection from isometric projection:Orthographic projection from isometric projection.

52.Orthographic projection from isometric projection:Orthographic projection from isometric projection.

53.Orthographic projection from isometric projection:Orthographic projection from isometric projection.

54.Reading of fabrication drawing:Reading of fabrication drawing.

55.Reading of fabrication drawing:Reading of fabrication drawing.

56.Reading of fabrication drawing:Reading of fabrication drawing.

57.Reading of fabrication drawing:Reading of fabrication drawing.